|
| Languages |
|
Роза вітрів:
The rolls of the Prinzing trade mark differ from the analogues by the exact shaping of the pipe, the ideal rounding of the metal, which makes it possible to produce pipes that are optimally suitable for the subsequent welding of the butt to the joint. Since it is very important that when the two ends of the pipe are brought together, no gaps remain either along the edges or in the middle.
This allows you to weld pipes, including thin-walled, without additives and to obtain excellent product quality. In addition, the counter, located on the right side of the rollers, makes it possible to quickly select the necessary clearance between the rollers for each required pipe diameter. A convenient clamping, as well as an easily open upper shaft clamp, allows the finished pipe to be extracted very quickly.
An experienced tinsmith will say that these rolls take into account everything necessary to ensure the speed and quality of production. To ensure the ideal rollout and the ability to work with mirror surfaces and copper, you can order the option of polished shafts, and for working at the thickness limit, the option of the rooted shafts.
Rollers are so easy to handle that you can train them quickly enough. After all, all adjustment is made with just one handle on the digital indicator of the gap counter. Unlike many others where the shaft is exposed from two sides.
You can get acquainted with the work of the rollers in our production, where you can visually demonstrate their advantages, and you can also make a pipe sample.
Hand-rolling units are successfully used for the processing of soft metals. Devices with manual control make the operation of the units more safe.
In addition to manually operated rollers, there are machines with electric drive. In models with the electric drive necessarily there is a brake. Electromechanical machines are used for large production volumes. Rollers for metal with electric drive operate from the electrical voltage and release the operators monitoring the operations performed with the help of this equipment from physical activity. Electromechanical rollers for sheet metal are devices operating due to rotation used for cold processing of sheet metal blanks.
Large machines controlled by automatics, themselves put the shafts in the desired position, adjusting them to the desired thickness of the metal sheet and the configuration of the workpiece. From overload the equipment is protected by a special electronic system.
The Rose of Vetrov group of companies manufactures and sells electromechanical rollers.
Rollers GPK - 1300/150
♦ The length of the working part of the shafts is 1300 mm, the diameter is 150 mm.
♦ The rollers are capable of processing metal with a thickness of 5 mm. Equipped with a cone roll-out device.
♦ Controlled by two reverse pedals.
♦ Rollers cost 7200 €
We also supply German PRINZING RME electro-mechanical rollers that will increase the productivity of your production and establish a serial production of products.
Prinzing RME - Electrically driven three roller rollers have proven for decades their high flexibility and reliability for the professional craft and industry. The bending process is carried out by means of an electric drive of the upper and lower shaft.
The single-stage motor operates via a dual footswitch to control forward and reverse travel.
The required bending diameter is adjusted manually using the rear shaft adjusting screw and is equipped with a measuring scale. In the fully automatic version of the machine, the rear shaft is also equipped with a drive.
The roll diameter ranges from 20 mm to 120 mm and a length of just over 200 mm to about 2.5 m.
The rollers are asymmetrically positioned. Quick and easy removal of finished pipes is ensured by the quick-release shaft fixation.
The rolls are spherical depending on the diameter. The machine can also be equipped with hardened, ground or rubberized shafts.
|
|
Prinzing RME 30/33 - 7670 € Electromechanical rolls Prinzing RME 30/33 are used for the production of thin sheet metal cylindrical pipes, shells and cones with a minimum diameter of 45 mm. In comparison with manual, this is a productive machine, as standard equipped with the following equipment: asymmetrically located shafts, the top shaft with a folding gate and the ability to rotate during the removal of parts, the tapering of the parts by installing at an angle of the rear shaft, the fast preload of the workpiece by the lower shaft, the movement of the rear shaft by means of the lead screw with its precise positioning in the vernier, the main drive through gearbox from a brake-equipped motor. Electromechanical rolls Prinzing RME 30/33 with a working length of 330 mm and a shaft diameter of 30 mm serve for sheet metal thickness up to 1.0 mm. As standard, the shaft strength is 700N / mm2, but if the customer wishes, the shafts can have a ground surface, surface or bulk hardening, have a groove and grooves for the wire on the shafts. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a motor with smooth start and speed adjustment, driven by three shafts. |
||||||||||||||||||||||
|
|
Prinzing RME 42/53 7980 € Electromechanical rolls Prinzing RME 42/53 are used for the production of thin sheet metal cylindrical pipes, shells and cones with a minimum diameter of 65 mm. In comparison with manual, this is a productive machine, as standard equipped with the following equipment: asymmetrically located shafts, the top shaft with a folding gate and the ability to rotate during the removal of parts, tapering the formation of parts by installing at an angle of the rear shaft, rapid preload of the workpiece by the bottom shaft, the rear shaft with the help of a lead screw with its precise positioning on the nonius, the main drive through the reducer from the brake-equipped motor. Electromechanical rolls Prinzing RME 42/53 with a working length of 530 mm and a shaft diameter of 42 mm serve for sheet metal thickness up to 1.5 mm. As a standard, the shaft strengths are 700N / mm2, but if the customer wants, the shafts can have a ground surface, a volume or surface hardening, a grooved groove and embedded grooves for the wire on the shafts. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with smooth start and speed adjustment, a drive for three shafts
|
||||||||||||||||||||||
|
|
Prinzing RME 52/53 - 8150 € Electromechanical rolls Prinzing RME 52/53 are used for the production of thin sheet metal cylindrical pipes, shells and cones with a minimum diameter of 65 mm. In comparison with manual, this is a productive machine, as standard equipped with the following equipment: asymmetrically located shafts, the top shaft with a folding gate and the ability to rotate during the removal of parts, tapering the formation of parts by installing at an angle of the rear shaft, rapid preload of the workpiece by the bottom shaft, the rear shaft with the help of a lead screw with its precise positioning on the nonius, the main drive through the reducer from the brake-equipped motor. Electromechanical rollers Prinzing RME 52/53 with a working length of 530 mm and a shaft diameter of 52 mm serve for sheet metal thickness up to 1.5 mm. As a standard, the shaft strengths are 700N / mm2, but if desired, the shafts can have a ground surface, bulk or surface hardening or rubber covered, have a groove and groove for the wire on the shafts. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with smooth start and speed adjustment, a drive for three shafts |
||||||||||||||||||||||
|
|
Prinzing RME 42/103 - 8950 € Electromechanical rolls Prinzing RME 42/103 are used for the production of thin sheet metal cylindrical pipes, shells and cones with a minimum diameter of 65 mm. In comparison with manual, this is a productive machine, as standard equipped with the following equipment: asymmetrically located shafts, the top shaft with a folding gate and the ability to rotate during the removal of parts, tapering the formation of parts by installing at an angle of the rear shaft, rapid preload of the workpiece by the bottom shaft, the rear shaft by means of the lead screw with its precise positioning in the nonius, the main drive through the reduction gear from the brake-equipped single-stage motor. Electromechanical rolls Prinzing RME 42/103 with a working length of 1030 mm and a shaft diameter of 42 mm serve for sheet metal thickness up to 0.6 mm. As a standard, the shaft strengths are 700N / mm2, but if the customer wants, the shafts can have a ground surface, a volume or surface hardening, a grooved groove and embedded grooves for the wire on the shafts. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with soft start and manual speed adjustment, a lubricating syringe. |
||||||||||||||||||||||
|
|
Prinzing RME 52/103 - 9260 € Electromechanical rollers Prinzing RME 52/103 are designed for the manufacture of metal sheet shells and cones with a minimum diameter of 78 mm. Compared with hand-held, these are powerful machines with the following equipment: asymmetrical shaft arrangement, top shaft with a folding gate and the ability to rotate during the removal of parts, tapering of parts by mounting at an angle of the rear shaft, fast installation of the lower shaft, displacement the rear shaft with the help of the spindle and its precise positioning on the vernier, drive through the gearbox from the brake-equipped motor. Electromechanical rolls Prinzing RME 52/103 with a working length of 1030 mm and shaft diameters of 52 mm serve for sheet metal thickness up to 1.2 mm. As a standard, the strength of 700N / mm2 shafts and their volume heat treatment, but if desired, the shafts can have a ground surface and surface hardening, have on the shafts a groove groove and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with a smooth start and manual speed control, a two-stage main drive and a drive for all three shafts. |
||||||||||||||||||||||
|
|
Prinzing RME 60/103 - 10370 € Electromechanical rolls Prinzing RME 60/103 are designed for the manufacture of metal sheet cylindrical shells and cones with a minimum diameter of 90 mm. In comparison with manual, this is a powerful powerful machine with the following equipment as standard: asymmetric shaft arrangement, top shaft with a folding bolt and the ability to rotate during the removal of parts, tapering of parts by mounting at an angle of the rear shaft, fast installation of the lower shaft, displacement the rear shaft by means of the lead screw and its precise positioning on the nonius, the main drive through the gearbox from the brake-equipped single-stage motor. Electromechanical rolls Prinzing RME 60/103 with a working length of 1030 mm and shaft diameters of 60 mm serve for sheet metal thickness up to 1.5 mm. As a standard, the shafts are thermally improved and have a strength of 700 N / mm2, but if desired, the shafts can have a polished surface, surface hardening, have a rebate groove and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with smooth start and manual speed control, a drive for three main shafts or a two-stage main drive, a lubricating syringe . |
||||||||||||||||||||||
|
|
Prinzing RME 70/103 - 10790 € Electromechanical rolls Prinzing RME 70/103 are used for the production of thin sheet metal cylindrical pipes, shells and cones with a minimum diameter of 105 mm. In comparison with manual, this is a productive machine, as standard equipped with the following equipment: asymmetrically located shafts, the top shaft with a folding gate and the ability to rotate during the removal of parts, tapering the formation of parts by installing at an angle of the rear shaft, rapid preload of the workpiece by the bottom shaft, the rear shaft with the help of the lead screw with its precise positioning on the vernier, the main drive through the reducer from the brake-equipped one high-speed motor. Electromechanical rolls Prinzing RME 70/103 with a working length of 1030 mm and a shaft diameter of 70 mm serve for sheet metal thickness up to 1.8 mm. As a standard, the strength of heat-treated shafts is 700N / mm2, but if desired, the shafts can have increased hardness in surface hardening and polished surface, have a groove on the shafts and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with smooth start and manual speed control, a drive for three main shafts, two speed drives, and a lubricating syringe. |
||||||||||||||||||||||
|
|
Prinzing RME 85/103 - 18900 € Electromechanical rollers Prinzing RME 85/103 are used for the production of thin sheet metal cylindrical pipes, shells and cones with a minimum diameter of 125 mm. This is a productive machine that has the following equipment as standard: asymmetrically located shafts, a top shaft with a folding bolt and the ability to rotate when removing parts, tapering the parts by installing at an angle of the rear shaft, fastening the workpiece with the lower shaft, moving the rear shaft by running screw with its precise positioning on the nonius, the main drive through the reducer from the brake-equipped one high-speed motor. Electromechanical rolls Prinzing RME 85/103 with a working length of 1030 mm and a shaft diameter of 85 mm are capable of bending sheet metal up to 2.5 mm thick. As a standard, the shafts are thermally treated and have a strength of 700N / mm2, but if desired, the shafts can have additional surface hardening, polished surface, have on the shafts a groove and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with smooth start and manual speed control, a drive for three main shafts and two high-speed motors. |
||||||||||||||||||||||
|
|
Prinzing RME 100/103 - 22100 € Electromechanical rollers Prinzing RME 100/103 are used for the production of thin sheet metal cylindrical pipes, shells and cones with a minimum diameter of 150 mm. In comparison with manual, this is a productive machine, as standard equipped with the following equipment: asymmetrically located shafts, the top shaft with a folding gate and the ability to rotate during the removal of parts, tapering the formation of parts by installing at an angle of the rear shaft, rapid preload of the workpiece by the bottom shaft, the rear shaft with the help of a spindle with its precise positioning on the vernier, drive through the gearbox from the brake-equipped one high-speed motor. Electromechanical rolls Prinzing RME 100/103 with a working length of 1030 mm and a shaft diameter of 100 mm serve for sheet metal thickness up to 3.2 mm. The standard strength of thermally treated shafts is 700N / mm2, but additionally the shafts can have surface hardening, ground surface, grooved groove and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, an electric drive for the rear shaft, a motor with a smooth start and manual speed control, two high-speed drive and three main drive shaft. |
||||||||||||||||||||||
|
|
Prinzing RME 120/103 - 32280 € Electromechanical rollers Prinzing RME 120/103 are used for the production of thin sheet metal cylindrical pipes, shells and cones with a minimum diameter of 180 mm. In comparison with manual, this is a productive machine, as standard equipped with the following equipment: asymmetrically located shafts, the top shaft with a folding gate and the ability to rotate during the removal of parts, tapering the formation of parts by installing at an angle of the rear shaft, rapid preload of the workpiece by the bottom shaft, the rear shaft with the help of a lead screw with its precise positioning on the nonius, drive through the reduction gear from the brake-equipped one speed motor. Electromechanical rolls Prinzing RME 120/103 with a working length of 1030 mm and a shaft diameter of 120 mm serve for sheet metal thickness up to 4.5 mm. As a standard, the strength of heat treated shafts is 700N / mm2, but the shafts can additionally undergo surface hardening and have increased hardness, polished surface, rebate groove and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with a smooth start and manual speed adjustment, an electric drive for the rear shaft, a drive for three main shafts, two high-speed drive. |
||||||||||||||||||||||
|
|
Prinzing RME 52/128 - 10530 € Electromechanical rollers Prinzing RME 52/128 are designed for the manufacture of metal sheet cylindrical shells with a minimum diameter of 78 mm and cones. In comparison with manual, this is a powerful powerful machine with the following equipment as standard: asymmetric shaft arrangement, top shaft with a folding bolt and the ability to rotate during the removal of parts, tapering of parts by mounting at an angle of the rear shaft, fast installation of the lower shaft, displacement the rear shaft with the help of the spindle and its exact positioning on the vernier, drive through the gearbox from the brake-equipped one high-speed motor. Electromechanical rolls Prinzing RME 52/128 with a working length of 1280 mm and shaft diameters of 52 mm serve for sheet metal thickness up to 0.9 mm. As standard, the shaft strength is 700N / mm2 and their thermal improvement, but if desired, the shafts can have a surface hardening and ground surface, have on the shafts a groove groove and embedded grooves for the wire. Additionally, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with soft start and manual speed control, a two-stage main drive and a three-shaft drive. |
||||||||||||||||||||||
|
|
Prinzing RME 60/128 - 12270 € Electromechanical rollers Prinzing RME 60/128 are designed for the manufacture of metal sheet cylindrical shells with a minimum diameter of 90 mm and cones. In comparison with manual, this is a powerful powerful machine with the following equipment as standard: asymmetric shaft arrangement, top shaft with a folding bolt and the ability to rotate during the removal of parts, tapering of parts by mounting at an angle of the rear shaft, fast installation of the lower shaft, displacement the rear shaft by means of a spindle and its exact installation on the vernier, the main drive through the gearbox from the brake-equipped single-stage engine. Electromechanical rolls Prinzing RME 60/128 with a working length of 1280 mm and shaft diameters of 60 mm serve for sheet metal thickness up to 1.2 mm. As standard, heat-treated shafts with a strength of 700N / mm2, but if the customer wants, the shafts can have a polished surface, increased hardness in surface hardening, have a groove on the shafts and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a lateral stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with smooth start and manual speed control, a drive for three main shafts, a two-stage main drive, a lubricating syringe . |
||||||||||||||||||||||
|
|
Prinzing RME 60/153 - 12940 € Electromechanical rollers Prinzing RME 60/153 are used for the manufacture of cylindrical pipes, shells with a minimum diameter of 90 mm and cones made of thin sheet metal. In comparison with manual, this is a productive machine, as standard equipped with the following equipment: asymmetrically located shafts, the top shaft with a folding gate and the ability to rotate during the removal of parts, tapering the formation of parts by installing at an angle of the rear shaft, rapid preload of the workpiece by the bottom shaft, the rear shaft with the help of the spindle and its precise positioning on the vernier, drive through the gearbox from the brake-equipped motor. Electromechanical rollers Prinzing RME 60/153 with a working length of 1530 mm and a shaft diameter of 60 mm serve for sheet metal thickness up to 0.8 mm. As a standard, the strength of heat-treated shafts is 700N / mm2, but if desired, the shafts can have a polished surface, increased hardness from surface hardening, and have a groove groove and embedded grooves on the shafts. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with smooth start and manual speed control, two high-speed main drive and a three-shaft drive. |
||||||||||||||||||||||
|
|
Prinzing RME 70/153 - 13860 € Electromechanical rollers Prinzing RME 70/153 are used for the production of thin sheet metal cylindrical pipes, shells with a minimum diameter of 100 mm and cones. In comparison with manual, this is a productive machine, as standard equipped with the following equipment: asymmetrically located shafts, the top shaft with a folding gate and the ability to rotate during the removal of parts, tapering the formation of parts by installing at an angle of the rear shaft, rapid preload of the workpiece by the bottom shaft, the rear shaft with the help of a spindle and its precise positioning on the nonius, the main drive through the reducer from the brake-equipped single-stage engine. Electromechanical rollers Pinzing RME 70/153 with a working length of 1530 mm and a shaft diameter of 70 mm serve for sheet metal thickness up to 1.2 mm. As a standard, the strength of heat-treated shafts is 700N / mm2, but if desired, the shafts can have increased hardness during surface hardening, polished surface, have a groove groove and embedded grooves on the shafts. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with smooth start and manual speed control, a drive for three main shafts and two high-speed drives. |
||||||||||||||||||||||
|
|
Prinzing RME 85/153 -21270 € Electromechanical rollers Prinzing RME 85/153 are used for the production of thin sheet metal cylindrical pipes, shells with a minimum diameter of 125 mm and cones. This is a productive machine that has the following equipment as standard: asymmetrically located shafts, a top shaft with a folding bolt and the ability to rotate when removing parts, tapering the parts by installing at an angle of the rear shaft, fastening the workpiece with the lower shaft, moving the rear shaft by running screw with its exact positioning on the nonius, the main drive through the gearbox from the brake-equipped single-stage engine. Electromechanical rolls Prinzing RME 85/153 with a working length of 1530 mm and a shaft diameter of 85 mm are capable of bending sheet metal up to 1.8 mm thick. As a standard, the thermally treated shafts have a strength of 700N / mm2, but if desired, the customer can have increased hardness in surface hardening, have a ground surface, grooved groove and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with soft start and manual speed control, a two-speed drive or a drive for three main shafts. |
||||||||||||||||||||||
|
|
Prinzing RME 100/153 - 22270 € Electromechanical rollers Prinzing RME 100/153 are used for the production of thin sheet metal cylindrical pipes, shells with a minimum diameter of 150 mm, cones. This is a productive machine that has the following equipment as standard: asymmetrically located shafts, a top shaft with a folding bolt and the ability to rotate when removing parts, tapering the parts by installing at an angle of the rear shaft, fastening the workpiece with the lower shaft, moving the rear shaft by running screw with its exact positioning on the nonius, the main drive through the gearbox from the brake-equipped single-stage engine. Electromechanical rollers Prinzing RME 100/153 with a working length of 1530 mm and a shaft diameter of 100 mm are capable of bending sheet metal up to 2.4 mm thick. As a standard, the strength of heat treated shafts is 700N / mm2, but the shafts can additionally undergo surface hardening and have increased hardness, have a ground surface, a groove groove and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a lateral stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with smooth start and manual speed control, an electric drive for the rear shaft, a drive for three main shafts and a two-speed drive . |
||||||||||||||||||||||
|
|
Prinzing RME 120/153 - 32270 € Electromechanical rollers Prinzing RME 120/153 are used for the production of thin sheet metal cylindrical pipes, shells with a minimum diameter of 180 mm and cones. This is a productive machine that has the following equipment as standard: asymmetrically located shafts, a top shaft with a folding bolt and the ability to rotate when removing parts, tapering the parts by installing at an angle of the rear shaft, fastening the workpiece with the lower shaft, moving the rear shaft by running screw with its exact positioning on the nonius, the main drive through the gearbox from the brake-equipped single-stage engine. Electromechanical rollers Prinzing RME 120/153 with a working length of 1530 mm and a shaft diameter of 120 mm serve for sheet metal thickness up to 3.5 mm. The standard strength of heat-treated shafts is 700N / mm2, but additionally the shafts can undergo surface hardening and have increased hardness, have a ground surface, grooved groove and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a main motor with a smooth start and manual speed adjustment, an electric drive for the supply of the rear shaft, a two-speed drive. |
||||||||||||||||||||||
|
|
Prinzing RME 70/203 - 15650 € Electromechanical rollers Prinzing RME 70/203 are used for the production of thin sheet metal cylindrical pipes, shells with a minimum diameter of 105 mm, cones. In comparison with manual, this is a productive machine, as standard equipped with the following equipment: asymmetrically located shafts, the top shaft with a folding gate and the ability to rotate during the removal of parts, tapering the formation of parts by installing at an angle of the rear shaft, rapid preload of the workpiece by the bottom shaft, the rear shaft with the help of the lead screw with its precise positioning on the vernier, the main drive through the reducer from the brake-equipped one high-speed motor. Electromechanical rolls Prinzing RME 70/203 with a working length of 2030 mm and a shaft diameter of 70 mm serve for sheet metal thickness up to 0.8 mm. As a standard, the strength of thermally improved shafts is 700N / mm2, but if desired, the shafts can have a surface hardening and ground surface, have on the shafts a groove groove and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side support, a pneumatic bending device with a fourth shaft and automatic program control, a drive for three main shafts, two high-speed main drive. |
||||||||||||||||||||||
|
|
Prinzing RME 85/203 - 22960 € Electromechanical rollers Prinzing RME 85/203 are used for the production of thin sheet metal cylindrical pipes, shells with a minimum diameter of 125 mm, cones. This is a productive machine that has the following equipment as standard: asymmetrically located shafts, a top shaft with a folding bolt and the ability to rotate when removing parts, tapering the parts by installing at an angle of the rear shaft, fastening the workpiece with the lower shaft, moving the rear shaft by running screw with its precise positioning on the nonius, the main drive through the reducer from the brake-equipped one high-speed motor. Electromechanical rollers Prinzing RME 85/203 with a working length of 2030 mm and a shaft diameter of 85 mm are capable of bending sheet metal up to 1.2 mm thick. As a standard, the shaft strengths are 700N / mm2, but if desired, the shafts can have increased hardness from surface hardening or are covered with rubber, have a ground surface, or have a groove and groove for the wire on the shafts. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with soft start and manual speed control, two speed drives and a drive for three main shafts. |
||||||||||||||||||||||
 |
Prinzing RME 100/203 - 27410 € Electromechanical rollers Prinzing RME 100/203 are used for the production of thin sheet metal cylindrical pipes, shells and cones with a minimum diameter of 150 mm. This is a productive machine that has the following equipment as standard: asymmetrically located shafts, a top shaft with a folding bolt and the ability to rotate during the removal of parts, tapering the parts by mounting at an angle of the rear shaft, fast pressing the workpiece with the lower shaft, screw with its precise positioning on the nonius, the main drive through the reducer from the brake-equipped one high-speed motor. Electromechanical rollers Prinzing RME 100/203 with a working length of 2030 mm and a shaft diameter of 100 mm are able to bend sheet metal up to 1.8 mm thick. The standard strength of heat-treated shafts is 700N / mm2, but additionally the shafts can have surface hardening and increased hardness, have a ground surface, a groove groove and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a lateral stop, a pneumatic bending device with a fourth shaft and automatic program control, a motor with smooth start and manual speed control, an electric drive for the rear shaft, a drive for three main shafts and a two-speed drive . |
||||||||||||||||||||||
|
|
Prinzing RME 120/203 - 37900 € Electromechanical rolls Prinzing RME 120/203 are used for the production of thin sheet metal cylindrical pipes, shells and cones with a minimum diameter of 180 mm. This is a productive machine that has the following equipment as standard: asymmetrically located shafts, a top shaft with a folding bolt and the ability to rotate when removing parts, tapering the parts by installing at an angle of the rear shaft, fastening the workpiece with the lower shaft, moving the rear shaft by running screw with its precise positioning on the nonius, the main drive through the gearbox from the brake-equipped single-speed motor. Electromechanical rollers Prinzing RME 120/203 with a working length of 2030 mm and a diameter of shafts of 120 mm are able to bend sheet metal up to 2.5 mm thick. The standard strength of heat-treated shafts is 700N / mm2, but additionally the shafts can have surface hardening and increased hardness, have a ground surface, a groove groove and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a side stop, a pneumatic bending device with a fourth shaft and automatic program control, an electric drive for the rear shaft, a main motor with a smooth start and manual speed control, a drive for three main shafts and a two-speed drive. |
||||||||||||||||||||||
|
|
Prinzing RME 120/253 - 40380 € Electromechanical rollers Prinzing RME 120/253 are used for the production of thin sheet metal cylindrical pipes, shells and cones with a minimum diameter of 180 mm. This is a productive machine that has the following equipment as standard: asymmetrically located shafts, a top shaft with a folding bolt and the ability to rotate when removing parts, tapering the parts by installing at an angle of the rear shaft, fastening the workpiece with the lower shaft, moving the rear shaft by running screw with its precise positioning on the nonius, the main drive through the reducer from the brake-equipped one high-speed motor. Electromechanical rollers Prinzing RME 120/253 with a working length of 2530 mm and a shaft diameter of 120 mm are able to bend sheet metal up to 1.5 mm thick. As a standard, the strength of heat-treated shafts is 700N / mm2, but additionally, the shafts can undergo surface hardening and have increased hardness, polished surface, have on the shafts a groove groove and embedded grooves for the wire. In addition, the rollers can be equipped with a side stop for conical rolling, a support table with a lateral stop, a pneumatic bending device with a fourth shaft and automatic program control, an electric drive for the rear shaft, a main motor with a smooth start and manual speed adjustment, driven by three main shafts, drive. |
